my climate regulate works however doesn't throw warm or A/C mechanic claimed it's the blender on the optimal of the dashboard or the wiring i beg your pardon it to be messed with. Need assist finding this pin out please.


You are watching: Driver side blend door actuator chevy silverado

*

good morning,The actuator is the most typical failure for the temperatures no changing. It is on height of the heater situation as your tech stated. This overview and video will display you just how to change it.https://youtu.be/Eqf-H3COtSoandhttps://www.neurosoup.org/articles/replace-blend-door-motorI attached the pinout of the module as you requested.https://www.neurosoup.org/articles/how-to-check-wiringI likewise attached the actuator instead of procedure and also location that the mix door for you. Examine out the diagrams (Below). Let us understand what happens and please upload images or videos of the problem.
*

*

*

*

truck blows hot air no issue what setting it is on. The system is full of Freon. Compressor go on and off in addition to the condenser cooling fans operating normally. I've i found it the high push side where the orifice tube is situated icing end going in in the direction of the firewall. Also, before the start of all this, there to be a popping noise comes from under the dash towards the floor board on the passenger side. I've also noticed that once the popping stopped, the is when it started blowing hot. The blend door seems to be operating correctly, yet not specifically sure where the temp manage actuator is located on this certain model. Any help on this would certainly be lot appreciated. Thanks!
Hello, This certainly sounds favor it can be a difficulty with your Heating Ventilation Air conditioning (HVAC) mix door actuator. Ns have had diagrams down below in the diagrams down below of the place of the blend door actuator for her vehicle. I likewise have included a connect for you to go to:https://www.neurosoup.org/articles/replace-blend-door-motor you re welcome go v the guides and get earlier to us with what you are able to uncover out.Thanks, Alexneurosoup.org
Is Fig. 2 because that a dual climate control and Fig. 3 for a single? just want come make certain im reading this right because I have a solitary control unit and also not a dual.
Hello again, figure 2 is Auto Climate Control and also Figure 3 is for digital Control. The means I view it is number two is when you collection a desired temperature and the vehicle maintains the cabin temperature because that you, and figure 3 is for you have to manually readjust the temperature yourself. It should be an alternative on your vehicle.Thanks, Alexneurosoup.org
ns have found that the heat/cool mix actuator is not constantly working and that I may need to change it but I carry out not know where it is located, when I take it the (3) 7 mm screws indigenous under the dash near the floor, then gotten rid of the cover ns did not see any kind of actuators just an ext plastic, so before I begin pull the totality thing apart or paying part crazy lot of money ns was wonder if you knew where it is situated or even have the exact diagram because that my truck? Thanks.
Hello, right here is a overview to aid you view where all blend door electric motors are with diagrams belowhttps://www.neurosoup.org/articles/replace-blend-door-motorTry pulling hvac fuse under hood because that 60 seconds an initial as it may reset the actuators. See pic for temp actuator, if you have both left and right temps this is additionally for best side. Inspect out the diagrams (Below) you re welcome let us know if you need anything rather to get the problem fixed.
The driver next vents would flip from AC to an extremely hot air. I watched the video clip and changed the blend door actuator. Did the re-calibration by disconnecting the battery for about fifteen minutes, reconnect and turn the truck on for one minute. Turn off a couple of minutes and turn on again two minutes. I can hear a ratchet sound throughout the process. Currently it is warm all the time and very little air volume coming from the passenger side vents. What deserve to I perform to settle this? Thanks.
feather at your diagrams, it shows up I changed the dorn actuator. The one I replace is displayed in your photo below under the cowl top top the passenger side. Is the exactly one under the peak of the dash? execute you have a video clip showing how to acquire to it?
that is correct. The is not the actuator. The exactly one is under the dash, left side over the fuel pedal.I attached a snapshot and the procedure. Basic replacement.RoyREMOVAL PROCEDURE 1. Eliminate the I/P insulator panel.ImageZoom/Print 2. Disconnect the electric connector (1) indigenous the left waiting temperature actuator (2). 3. Remove the screws from the left wait temperature actuator (2). 4. Eliminate the left wait temperature actuator (2) from the HVAC module assembly (3).


See more: Giving Someone A Raspberry Mean? What Does Giving Someone The Raspberry Mean

now I am confused. Follow to what I have read, the actuator top top the left over the gas pedal is the setting door. Many of the videos I have seen state that the hot/cold ~ above the driver next is regulated by the actuator ~ above the best side underneath, the one i replaced. I also think the neurosoup.org video stated or comprise that. Yet the chart on the neurosoup.org article suggested that the driver side hot/cold to be the actuator top top the optimal right next (not the recirculate). So i am reasoning that i did change the correct actuator, yet that one of two people my replacement part is no correct or i did the re-calibration wrong. I opened up the actuator that ns took out. It did not have actually the metal under the big gear, nor the monitor on the board choose all the ones in the videos have. I carry out not understand what that can mean. Outside, the actuators look at the same.