3 the end of 5 moderate Moderate. You must be relatively strong to dig the holes, mix the concrete, and also muscle heavy posts into position.

Tools & Materials

*

*

*

*

Q: mine fence door is sagging and dragging in the dirt. What have to I do?

—Cecile Bolduc, Hampton, N.H.

You are watching: How to fix a sagging fence gate

A: mockery Feeney replies: A gate is just as great as the articles it hangs from and latches to. Once gateposts space plumb and also rock solid, they will stand up to the swing and slam of every opening and closing. Yet when they"re loose in their holes or space weakened by rot or insects, then hinges revolve creaky, the latch won"t catch, and the gate can"t carry out its job.

A write-up that"s wobbly yet still solid deserve to be resolved quite conveniently by packing crushed stone around its base v a sledgehammer. However when a article is rotten, together both this gateposts were, it has to be removed and also replaced.

I invested 8 hours on this task digging the end the old gateposts and putting in new ones, which restored the old gate"s youthful firmness and satisfying snap. Follow this steps and you should be able to do the exact same for her sagging gate.

Josh Feeney is a fence installer with Walpole Woodworkers, which has actually installed fencing for many TOH TV projects.

Step 1

Gate

*
action 2

Remove the Hinge Post

*
photo by Webb Chappell eliminate the gate and collection it aside. Detach the fence section from the hinge post, then dig approximately the post until it wiggles freely. (If the write-up is collection in concrete, dig about it, then break it into little pieces through a sledgehammer.) come pull the end a post , provide it bear hug and straighten your knees. Use this old write-up as a template to mark the places of the hinges on the brand-new post.

Step 3

Set the new Hinge Post

*
picture by Webb Chappell Prop up the unsupported finish of the fence ar until it"s level. Now, fill in or destruction out the hinge-post hole till it"s 3 feet deep and also drop in the new post. Hold it upright in that hole and also check that its top is level through the optimal of the latch post. To make sure that the gate will certainly clear the floor by 2 come 5 inches, host a level at the elevation of the reduced hinge.

Step 4

Attach the Fence Section

*
photograph by Webb Chappell ar a level versus the side of the hinge post facing the gate opening. Once the level suggests that this side is vertical, attach the fence rails to the hinge short article with galvanized deck screws. Eliminate the prop under the fence section.

Tip: A wooden wedge reduced from a piece of old fence write-up makes a helpful prop when leveling gates and fence sections.

Step 5

Line up all the Posts

*
photo by Webb Chappell Tack a nail to the much side the the nearest fence post, about a foot over grade, and tie a mason"s line to it. Traction the line about the post"s corner and several feet past the latch post. Connect it come a stake so the the heat touches the latch post. Move the hinge article over till it just touches the line, and also make the plumb. A post is plumb when a level reflects that two nearby sides space vertical.

Step 6

Strengthen the Footing

*
photograph by Webb Chappell Brace the hinge article with 2 2x4s: Screw the studs" upper ends right into opposite political parties of the article 3 feet over grade, and stake the lower ends in the ground around 3 feet from the write-up base. Mix up 2 bags of concrete and fill approximately the post. Prevent filling as soon as the concrete is 3 come 4 inches below grade, sufficient to hide it under topsoil. Allow the mix cure overnight.

See more: Red Dead Redemption 2: How To Store Items On Horse Rdr2, : Reddeadredemption

Step 7

Rehang the Gate

*
photo by Webb Chappell If the latch short article rotted, together this one did, change it complying with steps 1 despite 4; girlfriend won"t need concrete. Set the short article in a 3-foot-deep hole on 2 inch of tamped gravel, examine that its optimal is even with the hinge post"s, then fill the hole with firmly compacted gravel and also soil. Reattach the gate, making certain its top rail is level and also that it gets rid of the ground by 2 to 5 inches. Near the gate and attach the latch whereby its bolt access time the latch post.