No issue which automobile you drive, girlfriend will constantly have some replacement and repair work-related to perform every therefore often. As soon as you listen a squeaky sound each time you step on the clutch pedal, it means you have actually a faulty clutch slave cylinder. There is no it, girlfriend will struggle to move gears. Over time, the clutch slave cylinder will capture up v some wear and tear every time you depress the clutch, because of this requiring a replacement due to the fact that repairs have the right to be quite tricky.

You are watching: How to replace clutch slave cylinder ford f150

With the appropriate tools and the ideal slave cylinder, replacement is quite simple task. Eliminate the old slave cylinder first, replace it and bleed that out and also do a check drive.

The clutch slave cylinder works in addition to the clutch grasp cylinder because that disengagement. So just how does the clutch servant cylinder work? when you press on the clutch pedal, the clutch grasp cylinder applies a particular amount of press on the clutch slave cylinder, which move the pressure plates to relax the clutch indigenous the engine of your F150, enabling you to move gears smoothly.


First points first.

What’s the difference in between brake fluid and clutch fluid?

Brake fluid is the exact same as clutch fluid. We use the phrase clutch fluid and brake liquid interchangeably. The fluid that goes right into your brake device is the exact same hydraulic liquid used in the clutch reservoir. Over there is no separation, personal, instance clutch fluid. Since brake system repairs are an ext common, manufacturers determined to call it brake fluid, no clutch fluid.

Signs that Its Time to replace the Clutch slave Cylinder

When a clutch servant cylinder starts come fail, there will always be remarkable signs. A failing clutch servant cylinder will certainly not be able to transition gears properly, and also other issues will begin to present. The challenge may be identifying the signs of a negative clutch servant cylinder. Ignoring any type of of the signs of a failing clutch slave cylinder the we will explain listed below can reason further damages to your vehicle. Here’s what come look the end for;

Differences in the clutch pedal feel and also application

Any unusual loosened or soft feeling in the clutch pedal signifies a difficulty with the clutch slave cylinder or liquid pressure. It can be the clutch pedal pushes to the floor without engaging the clutch in ~ all. The clutch liquid may not be able to go all the means to the servant cylinder to engage the clutch.

Clutch fluid leaks

Low clutch fluid in the reservoir method there is a leak in the system, one of two people at the servant or master cylinder. Leakages come native a fault seal, valve, or hose, i m sorry degrade end time and develop cracks. Friend will understand there is a leak once the levels room low after a refill the the clutch fluid or in ~ a quick time.


Dark clutch fluid

Dirty clutch fluid is additionally a authorize of worn-out seals in the clutch system. Piece of the rubber seals break down and contaminate the clutch fluid, which eventually affects suitable transmission.

Gear shifting issues

Any concerns with an altering gears once you drive median there is an issue with the master or servant cylinder. Inner leaks and tears will impact the servant cylinder’s capacity to displace liquid properly, which will not release the clutch properly as soon as pressed.

Where is the servant Cylinder on a Ford F150?

It is crucial to understand the place of the servant cylinder once the clutch device starts showing difficulties that you will need to fix. Girlfriend will find the slave cylinder on one F150 joined to the clutch understand cylinder. The understand cylinder is situated on the firewall beside the brake grasp cylinder v a hose.

Check this too: F150 Bogs Down as soon as Accelerating: possible Causes

You will need to look under the truck and see lines coming out of a bleeder valve to access it. The slave cylinder is ~ above the left side, within the bell housing, and also controls the clutch release fork.


How execute You eliminate the Clutch servant Cylinder ~ above a Ford F150

Before removing the clutch servant cylinder, you need to do a fast inspection to confirm the leakages ~ above the slave cylinder. Assemble all the vital tools and also remove the old slave cylinder using the complying with steps.

What you will do it Need

Wrench setFloor jackFour jack standsRubber stopperRatchet screwdriverDrip panCreeperRagFord quick release disconnect toolRatchet through metric and standard socketsFlashlight

Directions

Prepare the auto for clutch removal.Park the truck on a flat surface.Use wheel chocks on the rear tires to avoid the van from moving and also engage the parking brake.Jack increase the truck with a floor jack and put it on jack stands. Location two jack stands under the rear axle and one jack under every eye beam top top the prior suspension. Elevator the auto until every the wheels are off the ground and also you have enough room under the truck.Disconnect the an adverse cord native the battery because that safety.Put a light under the automobile near the infection bell housing.Remove the bolts on the transmission skid plate making use of a socket and wrench. If over there is an exhaust pipe on peak of the skid plate, usage a socket to ease the exhaust pipeline hanger bracket and also push the aside.Locate the servant cylinder hydraulic line that goes right into the infection housing. That is a black, reinforced hose in the bell housing.Wipe the hydraulic clutch line v a rag and spray part penetrating oil on the clutch line joint and also let it soak for a while. Oiling the joint help it to loosen quickly without bending the line when removing it.Find the hanger bracket that holds the hydraulic heat in place and use a socket to ease the bolts. Execute not remove it entirely; let that hang loose until you’re prepared to take it out.Take her Ford rapid release disconnect tool and place the fork end in the seam in between the clutch heat sleeve and the finish of the clutch line. Fiddle the tool ago away from the transmission to compress the seal. Continue compressing that while you press in top top the hose through the other hand, then conveniently pull come disconnect the clutch line. Seal that end of the hydraulic line with a rubber stopper to store out the dirt.If you have an older F150 engine model, you need to use a screwdriver through the rapid release disconnect tool. Ar the disconnect tool in the sleeve seam and push the white seal into the joint. Remove the disconnect tool and use a flat-head driver to further force all sides of the white seal right into the clutch heat joint. Climate pull the hydraulic line and also plug the open finish with a rubber stopper.Go back to the loose hydraulic line, very closely disconnect the servant cylinder and the push-rod out without bending the hydraulic clutch line, and also put it aside. Note exactly how all the components fit in so the you can refit ago together.

Replacing the Clutch servant Cylinder

A faulty slave cylinder will certainly cause challenge in changing or no moving at all. You can replace a brand-new slave cylinder making use of the following steps. Save in mind that you may need one assistant to aid with bleeding the servant cylinder.


The brand-new slave cylinder will certainly come through a plastic strap, additionally called a slave cylinder retainer clip, approximately the connector end to hold the stick in place. Execute not remove this plastic strap. Press the clutch release arm forward and also insert your brand-new slave cylinder, then screw in the bolts and also tighten to secure it in place.Reconnect the hydraulic clutch line and then close the cap with a wrench and secure the tightly.Pour the clutch fluid into the clutch understand cylinder until it is full.Use a wrench to open the bleed valve top top the side of the servant cylinder and enable it to bleed into a drip pan. Permit it to bleed until you watch a steady drip through no air bubbles. The waiting in the hydraulic line will save the servant cylinder indigenous actuating the push from the grasp cylinder, making it an overwhelming to change your transmission.Close the bleeder valve and refill your master cylinder v clean clutch fluid.Get someone to assist bleed air the end of the servant cylinder. Open the bleeder valve top top the slave cylinder and also have someone action on the clutch pedal to the floor slowly and also hold that in place.While the pedal is ~ above the floor, tightly close the bleeder valve and also then have the human let go of the clutch pedal.Have the assistant pump the clutch pedal, and the rod in the servant cylinder will break the plastic strap. Check for good movement the the rod and also if there is little movement, bleed the servant cylinder again.

Correctly assembling the clutch slave cylinder is vital as it stays clear of the possible premature damages of the seals and also clutch. Many slave cylinders fail after negative installation or bleeding. Prior to installing your new clutch slave cylinder, here are some far-ranging preventive procedures to observe;

Ensure the size and also position the the brand-new slave cylinder’s hydraulic line match with the older F150 slave cylinder line.Use the correct mounting fasteners- screws, bolts, nuts- to prevent loose connections.The clutch slave cylinder should be ~ above the very same level as the bell housing prior to tightening the bolts and also nuts. Misalignment can reason slipping of the clutch components.Do no forget to bleed your clutch slave cylinder. Constantly flush out any type of old hydraulic fluid from the system before fitting the new slave cylinder.Avoid bleeding by swiftly pumping the clutch pedal. That will damages the inner seals and also cause leaking.Observe markings ~ above the journey place, which suggest the exactly orientation. Not correct installation the the journey plate will reason frictional warm that will damages the unit.

How difficult is that to readjust a clutch servant cylinder – have to I call a mechanic?

Changing a clutch slave cylinder is really straightforward if you have actually the best tools, the appropriate slave cylinder for your car, and also a small knowledge of the vehicle. That is also easier since it is easily available from under the car.

If you space a DIY fanatic, you have the right to easily readjust your clutch slave cylinder through some tools and also following the actions explained above in this article, but you may also need an extra collection of hand to assist with the bleeding process. Additionally, if friend need additional assistance with your clutch servant cylinder replacement, don’t hesitate to gain a skilled to help.

How lengthy does it take it to change a clutch slave cylinder?

It takes around 3-4 hrs to remove and replace a clutch slave cylinder, consisting of bleeding the hydraulic system. It might take at many 2 hours for someone currently familiar v the job. Sometimes if the slave cylinder has actually a leakage, that may indicate that the grasp cylinder has a similar problem. If you an alert a difficulty with the understand cylinder too, it may take around 8 hours to change both the understand cylinder and also the slave cylinder.

What tools carry out I need to readjust a clutch servant cylinder?

There are several tools girlfriend must have actually to efficiently remove and also install anew clutch slaver cylinder for her vehicle. Castle include;

The floor jack and jack represents lifting your automobile or the ground. The clutch servant cylinder is available from underneath the car.The flashlight will help you see underneath the vehicle. Girlfriend will need to correctly recognize the leakages and the materials you have to remove and replace.A set of metric and standard sockets and also a set of wrenches to help with the bolts and also nuts certain the parts in place. Castle come in different sizes, therefore it’s finest to have a complete collection of both tools. Securing the bolts and also nuts through the dorn tools deserve to prevent the components from securing the car frame well.Penetrating oil is a lubricant the will aid with loosening the old rusted nuts and also bolts. You have the right to spray it on all the bolts once removing the servant cylinder; they will loosen increase struggle-free.Brake liquid is a hydraulic liquid that transfers force into press in any hydraulic system of vehicles.A drip pan is a container for catching oil drips. That is optional to have; friend can constantly improvise and also use one empty steel container.Rubber stoppers are put at the end of the open lines to stop dirt indigenous entering the hydraulic system. Dirt have the right to contaminate the brake liquid causing hydraulic clutch problems.

See more: How Big Is 18 Inches To Cm, What Does 18 Inches Look Like

Check this too: Ford Cruise control Troubleshooting & How-to Guide

Conclusion

A clutch slave cylinder is an essential in the manual transmission system, and also it is crucial to replace a faulty one immediately. Fortunately, this article will help you remove and also reinstall a brand-new clutch slave cylinder for her Ford F150. If you proceed to have transmission issues, have actually a certified mechanic diagnose and also fix the problem.