Hello everyone, ns am Bren! I want to uncover plans for a pretty looking video game console shelf for my son’s 17 video game consoles (and counting). I freshly started using some structure plans native myoutdoorplans.com which has actually a lot of of good ideas because that both indoor and also outdoor carpentry projects. Lock didn’t have actually any specific plans yet led me come this site: imgur.com/gallery/8p2me. The cabinet was very nice looking however actual construction details no great. I decided to use this together a loosened plan to go by and also here room the steps I complied with to finish my project. That took around a week or 25 hrs in total at a expense of $200.

You are watching: Video game console cabinets

I had actually to decision on the dimensions and material to usage for the unit. V respect to structure material ns would need to use pine mainly due to its affordability. Some jobs did use plywood but I didn’t want to have to make a large number of cuts which would certainly make that more an overwhelming to ensure appropriate joins, sizing etc. Of course if friend don’t use plywood friend are minimal in the depth of the shelves using constant pine boards, the more comprehensive boards often tend to it is in cupped or warped one means or another. I did uncover a great compromise. The building material stores offer pine panels i m sorry are smaller pieces of pine joined together which space straighter 보다 the wider pine boards. You need to pick with them due to the fact that they can separation at the ends yet if the store has actually a large supply you have the right to easily uncover enough for your project. That is also less expensive 보다 the separation, personal, instance pine boards i beg your pardon run around $13 because that 1 X 12 X 6 knotty pine, the panels are around $10 each. Because that the dimensions ns did a couple of spreadsheet scenarios and also finally resolved on something that suited my needs.

There to be a number of things to think about when developing the unit, consisting of the broad of the hardwood being used, trying to use factory length board to alleviate the variety of cuts and ensuring all systems could be accommodated. I finished up getting 10 – 1X12X6 pine panels at a cost of about $110 consisting of tax. The final layout to be slightly different than my plan but not far off. I design the unit around 6’ shelves so I might use the factory lengths the the pieces. Of course you require to inspect the lengths simply to be sure and sand the edges, but all these panels seem to be really consistent in your length. Ns checked and sanded five of these for the horizontal shelves.


*

Video game console room plans


See complete plans for this job HERE. The free plans come with a finish cut list and also with lots of diagrams, so girlfriend can construct this shelf by yourself.

How to build a video game Console Cabinet

*

The console shelving unit native the plan on the website I supplied as a overview utilized routered cut in the political parties to affix the shelves. I chose to use pocket feet screws since I have actually a pocket feet kit and they have been extremely strong in perpendicular joining from the few projects I have actually completed for this reason far. I drilled 4 holes in each side the the underside of every shelf. It not so necessary exactly wherein the pocket feet are put as long as castle are fairly evenly spaced.

Next step was to cut the political parties to the compelled lengths, which would be 42“. I left a tiny lip at the optimal of the shelf around 1” high and also rounded the external corners utilizing the ½” ring router bit. In retrospect it could have looked neater to have the next flush through the peak shelf and also the corner rounded yet at the moment I thought the lip would certainly be better if items to be on the peak shelf.

Once the shelves and sides were reduced the just cuts remaining were the shelf dividers. Ns figured 9” would be a great size and fit all consoles. Former to creating the shelves, I had actually measured every consoles and also figured also with room for cartridges and the Wii 9” would fit everything. I collection up a protect against at specifically 9” top top the mitre witnessed so measuring would not be required for every shelf piece, I might just cut and also slide the plank along. Through 14 dividers to cut out that was vital to have even continuous cuts, the stop I had set up really facilitated this and also saved time together well.

The next step i took to be to affix the bottom shelf to the sides using pocket screws. I made a small mistake once I did this. I should have allowed the appropriate spacing because that the bottom trim which was 1X2, an interpretation the trim would certainly actually be 1 ½” high. Instead of enabling 1 1/2” native the height of the bottom shelf ns left 1 ½” in ~ the bottom the the bottom shelf. As a result, the bottom trim would certainly not go do the washing up to the bottom that the unit, that no huge deal however I should have realized prior to I fastened the bottom shelf. I had actually some helping hand to affix the bottom shelf and also used timber glue come ensure a solid initial bond. The is crucial to usage a flat surface when attaching the first shelf come ensure the joint is perpendicular and even on both sides. Ns traced out specifically where the shelf would be located before screwing it together.

Once the bottom shelf was in place the various other shelves were fairly easy to place. I provided two shelf dividers ~ above each finish as spacers top top the an initial shelf to find the location of each succeeding horizontal shelf. I can screw in the bag screws because that the shelf with the divider spacers in place which do attaching every shelf fairly easy. Its necessary to save downward pressure on the shelf together you screw that in therefore it remains in place. Repeat this process four times and all the shelves will be in place.

*

Once the shelves are in ar you need to connect the shelf dividers where required. The arrangement online provided a finishing nail gun but I determined to use 1 ¼” lumber screws. Because that the bottom shelves i glued and also screwed both sides of the dividers for stability. Because that the other shelves I provided wood glue but screwed the shelf indigenous the height down only. If you staggered the shelves you might screw native both sides however my bottom rows the shelves were symmetrical so the was not possible. Ns figured two lumber screws would hold the dividers in place because they were only giving separation and also once the unit was complete of solution the dividers would certainly be do the washing up to the shelves indigenous the weight above. Likewise the divider over would covering the screw feet from the shelf listed below so much less screw head sheathe up would be required. Ns took care to respond to sink every screws and filled any screw heads through wood putty and sanded together needed.

I provided 1X2 jaw trim for the front edges, first cutting the sides and attaching with wood glue and also 1 ½” complete nails. That is important to sand every edges to eliminate the sharpness and splintering edges. 2nd I reduced the 5 shelf trim pieces to fit and also glued and nailed them into place. Ultimately the divider trim was cut and also attached. When all trim piece were fit right into place I offered a nail collection to sink all nails heads into the wood. The I provided wood putty to to fill all nail heads and also sanded as soon as dry.

Now the the unit was constructed the backing required to it is in added. Ns went with 1/8” Masonite as the backboard as opposed to plywood since it was both much less expensive and easier to cut openings because that the connections for the video game consoles. I cut the Masonite come 6’ across and made keep in mind of which side the relations were compelled from every console and also traced 3” holes using a tiny paint can. I used a jig witnessed to cut the holes, the Masonite was simple to cut, i drilled a 1/2” pilot hole inside each hole and also cut from there. Because that the audio components that were more than 12” deep I reduced out the rectangular space required to extend out the back of the unit. As soon as I had actually the holes cut I tacked the backing right into place to ensure it every fit properly.

*

Next to be to decide on the finish for mine project. My boy loves sonic the hedgehog blue so ns went through Minwax water based deep ocean stain. ~ doing some research study it seemed prefer I should very first use Minwax water based pre-stain conditioner so I acquired some of that together well. For internal projects i think the water based commodities are the method to go, they make for easy clean up and have very low odour.

Prior to using the lumber conditioner, you need to do a great sanding job. If you ever wonder what would happen without a good sanding before application, it reasons a stormy application procedure and can reason uneven results. I provided my random orbit sander v 140 grit and then I supplied 220 grit on my B&D information sander end the entire surface.

*

The pre-stain conditioner deserve to be tricky stuff, you require to apply it, let the sink in and also then stain in ~ 3 hours. For a small project this would certainly be no problem however for big projects choose my console shelves you need to plan ahead. If you condition the whole unit you may not acquire the staining finish prior come 3 hours. It is feasible but finishing the project is no something you want to rush. I used the conditioner to top and also sides that the project, then relocated on to staining. Then ns did the optimal two shelf sections, climate the bottom two shelf sections in the very same manner. I used a 3” stain brush to use the conditioner, for the whole project ns used around ½ that a 1 together container. I functioned it in for this reason the wood looked wet come the touch and also left it about ½ hour before applying stain.

The stain was also a little bit of a tricky proposition for a beginner prefer me. The instructions speak you must brush top top the stain and also then wipe off the excess with a lint totally free cloth in ~ 3 minute of application. V a big project this would average a most application and wiping. I offered a 3” foam brush to apply the stain, I uncovered it much easier to manage the application v the foam brush as contrasted to a continual stain brush, there was much less run turn off over the edges. My plan of assault was:

a. Stain top and then wipe turn off excess b. Stain each side and then wipe off excess c. Stain each shelf cube and then wipe off excess d. Stain prior trim and also then wipe off excess

One point you need to have on hand is a an excellent supply of lint complimentary rags you space willing to throw away. I had actually some old lint free car to wash towels i was ready to component with for this reason I offered those. Also you need great disposable rubber gloves because this operation gets really messy. An initial I provided some leftover shelving to practice my technique. A good application of conditioner, followed up in 30 minutes by stain applied with the foam brush, immediately followed up with removing access stain by wiping the lint free clothes through the serial of the wood seemed to job-related well. You should make certain you acquire into the corners where the stain can build up. After around 6 hrs I had the entire unit stained and ready for protective coating. There to be a couple of lessons follow me the way.

a. Carry out not permit the stain sit much longer than couple of minute or it gets noticeably more an overwhelming to remove. b. Make certain all extra glue is removed before applying the stain, the stain will certainly not cover increase the glue, it simply makes it look worse. The very same goes for screw heads, make sure they room well filled and sanded. c. Save an eye on run off, if over there are any drips clean them up immediately.

*

I can have gone with two coats the stain however though my project looked an excellent with one coat. Because that protective coating I supplied Minwax water based Polycrylic, the was straightforward clean up and also fast drying. Again i went through the 3” foam brush because that application, I probably went v 6 of these brushes in complete for the entire project. I used 3 coats that the Polycrylic in total. It is essential to sand v 220 grit sandpaper between coats. I offered sanding block (home make of course) to ensure I spanned all surfaces. There is no sanding, subsequent applications are exceptionally rough. I understand this because I tried one ar without the sanding in between.

See more: Radar Ships In World Of Warships Radar Data, Radar And How To Deal With It

Once every the complete was finish the backing essential to it is in attached and consoles set up. I attached the backing v 1” finishing nails follow me the edges v a couple on each shelf come ensure it was effectively secure. Climate I placed the consoles in place, supplied Velcro come wrap up every the cords and also voila, the job was complete!

Thank you for analysis our project around how to develop a video video game console cabinet and us recommend you to examine out the rest of the projects. Give thanks to you Bren because that this an excellent project! friend instructions space amazing, as well! Don’t forget come LIKE and also SHARE our projects with your friends, by utilizing the social media widgets. I ordered it to be the very first that it s okay our recent projects.